Skip to content
atelier brutrated in cycles
Carpenter Trouser 360, 360 g/m² cloth, laid flat

day ground shows the piece as it ships · night ground shows it after long use

trousers

carpenter trouser 360

Hammer loop, rule pocket and a 360 g/m² canvas. The loop is sized for ordinary hand tools.

€125

euro, VAT included

Size

Flat measurements for every size are in the table below, taken after washing, with a tolerance of ±1 cm.

  • Delivery included above €150
  • 14 days to withdraw from receipt
  • Conformity and hidden-defect guarantees both apply

the figures

measured values, each with the method it came from

Cloth weight

360

g/m²

Measured on the finished cloth.

Abrasion

35,000cycles

EN ISO 12947-2

Martindale rub cycles to the stated end point.

Tear strength

52 N warp

47 N weft

EN ISO 13937-2

Figures are the values declared by the mill under the named method. They describe cloth under a laboratory test, not a garment on a job. 360 g/m², 35,000 cycles, 3 reinforced areas.

where it is reinforced

Reinforced at

  1. 01KneesKnees are double-layered across the full panel.
  2. 02Pocket edgesPocket edges are bartacked at both corners.
  3. 03Back pocketsBack pockets are bartacked and set on a doubled ground.

A reinforced point carries a second layer or a denser stitch. It moves the wear from one layer to two; it does not make the area exempt from wear. Where you work hardest is still where the garment will change first.

in detail

Hammer loop on the left, riveted at both ends. The rule pocket sits on the right thigh and takes a folding rule up to 60 cm.

The loop is intended for the weight of an ordinary claw hammer or a hand tool of similar mass. It is a garment feature, not rated lifting hardware.

Knees are doubled; pocket mouths and back pockets are bartacked.

Shrinkage

Pre-shrunk before cutting
Yes
Movement on first wash
2 %
Chart figures taken
After washing
Method
EN ISO 6330, 40 °C domestic wash

Metal parts

  • Hammer loop rivetsCopper-plated steel

Nickel release from parts in prolonged skin contact is within the REACH limit of 0.5 µg/cm² per week.

measurements

Flat measurements in centimetres, tolerance ±1 cm, taken after washing. The rule pocket adds roughly 2 cm to the thigh measurement on the right leg.

Flat measurements for Carpenter Trouser 360, in centimetres
SizeWaist, flatInseamThigh, flat
EU 38388029
EU 40408130
EU 42428231
EU 44448332
EU 46468433
EU 48488434
EU 50508535
EU 52528536
EU 54548637
how to measure a garment you already own

label and end of life

Fibre composition

100% cotton

Care

Machine wash 40 °C on a normal cycle. Wash with similar colours. Do not bleach. Tumble dry low or line dry. Iron medium. Do not dry clean.

Country of manufacture

Pending supplier declarationPublished from the mill’s own declaration. We do not state a country until that declaration is on file.

Sorting and producer responsibility

  • Woven from cotton fibre. Recyclable through the textile collection stream.
  • Sold without a polybag. Shipped in a recycled kraft mailer.
Producer identifier
Pending registration

The sorting mark shown here stands in for the official artwork, which is applied from the controlled source. How to sort this garment at end of life

before you order

Price
€125 in euro, VAT included. Delivery is added at checkout and shown in full before you pay.
Dispatch
Orders leave within two working days. Times and charges
Withdrawal
14 days from receipt, with a standard form. How it works
Guarantees
Conformity and hidden defects, both statutory, both free. What they cover

what buyers say

No reviews are published for this piece yet. When they are, every one of them will be tied to an order placed on this site and will carry the date it was written. We do not buy reviews, we do not write them ourselves, and we do not remove one because it is unflattering.

If you have bought this piece and want to say something about how it has worn, write to support@handsonclothing.store with your order reference.

others in trousers